The components, SK, Hyperion RPM/Phase Sensor, Align RCE-BL35X ESC. The Throttle/Governor Wizard is self explanatory. The only. Find great deals for Align Trex T-rex Sport Pro Rce-bl35x 35a Brushless ESC Speed Control Ka. Shop with confidence on eBay!. Anyone have any idea how to use a E sky a transmitter to program the Align RCE-BL35X esc. the esc will not go into programing mode.

Author: Mooguramar Goll
Country: Malta
Language: English (Spanish)
Genre: Sex
Published (Last): 16 December 2015
Pages: 450
PDF File Size: 1.89 Mb
ePub File Size: 6.48 Mb
ISBN: 279-7-31116-141-5
Downloads: 2884
Price: Free* [*Free Regsitration Required]
Uploader: Mamuro

In order to verify that aligh are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic. It’s flying now with transmitter set curves. The only thing I can’t find an answer to is: Thank you for any help. Thanks georgi, when I’m finished with the trial I’ll post the results.

The information seems to indicate there may be incompatibilities with any programmable ESC like the CC. I would prefer to run the SK governor. Comments will be appreciated, Thanks. Originally Posted by rce-bp35x. The Hyperion Phase Sensors arrived yesterday. Followed the georgi picture installation post and everything went smooth.

Is this a great site or what! I set the throttle with the throttle section wizard, Checked the RPM box. Set the Gear Ratio to RPM was overthat’s not right. Got back on the site and found an explanation of what poles are. Reset the Gear Ratio to The pole count is the number of magnets on the outrunner not the stator windings that you can see through the vents. Went through the Governor section of the Wizard. Did the RPM test at The throttle set wasand I even got a fake flight video while the Heli never left the table.

Align RCE-BL35X ESC Governor Mode – HeliFreak

Next, a real flight test as soon as the rain lets up. Got the maiden hover test done. It’s different and I’m a little timid because if I tip it over on concrete it will explode.


Gain was 33 Collective Management off. Normal, Throttle stick from 40 to 0 rather quick. Normal switch to hold. The blades don’t wlign a lot of inertia. Throttle stick at 40 pitch reduction real slow. Not a good method. Landing 4, Normal Switch to hold, might be ok on a soft surface.

Align Trex T-rex 450 Sport Pro Rce-bl35x 35a Brushless ESC Speed Control K10304a

The constant head speed feels better than the Governor Off settings. Hi, You are correct blades do not have much inertia. It is a lot easier on a larger heli. When you hit TH, did you increase the collective rce-b3l5x by moving the throttle stick up gradually? This will increase the lift and soften the landing.

If you have a sim practice rcd-bl35x it before you try it for real. I would check the pitch curves for hold and normal, see if they match each other?

I have been trying to fly Helli’s for 8 months and it sure is rce-bl35. My e has three hover flights and it seems to settle pretty soft when landing. In Hold the Sim just floats fce-bl35x from feet and if the real 11 lb monster comes close to the same it should be fun. Well The SK Governor worked well for a couple of days and then I started to have vibration problems, not the fault of the Governor.

Went through the usual try this try that. Discovered Hyperion has a computerized recording system so I purchased the parts I needed for bench testing. The problem was a broken pickup wire under the shrink wrap on the motor lead. Anyway the unit records a lot more data than just rpm and the Governor is back in business.

Here is a link to the Hyperion E-Meter stuff. If it wasn’t for the SK and the self level features I would have given up on Hellis 4 or 5 months rce-bl35z.


With 45 years in the computer industry before I retired 15 years ago my hat is off to the Skookum developers. As far as I can tell it is not interfering with the SK I wanted to route the Hyperion RPM sensor through the power buss and I found a post by “Castel” that gave two options, the second option worked great.

The spool-up is not what I expected to see in the graph. The rest of it right on. The vibration index is on the bench, blades removed with all the gears turning. The drawing gets glued on the inside of the canopy so I don’t forget where I plugged what.

Flight rcebl35x coming soon. Got a weather break just long enough to get a couple of 2 minute hovers in normal at First landing by throttle stick reduction and it’s ok. The second from about 7 feet hold switch on and that’s real smooth, lots of blade inertia. SK Governor is Alig S. Last edited by ds1rc; at Please click one of the Quick Reply icons in the posts above to activate Quick Reply.

Quote message in reply? In order to be able to post messages on the HeliFreak forums, you must first register. Posting Quick Reply – Please Wait. Remove Advertisements Sponsored Links. Originally Posted by ds1rc Yes I do. Options Quote message in reply? Register Now Algin order to be able to post messages on the HeliFreak forums, you must first register. Password Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site.